DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
full bulletin at NHTSA ↗2006 Nissan Quest steering problems
moderate 4 complaints filed with NHTSA · avg repair $700 · see steering across all vehicles →
Among the 5 model years of Nissan Quest in our records for steering problems, this one ranks #3 by owner-complaint volume.
Is there a fix? Manufacturer service bulletins
The manufacturer has issued service bulletins covering steering on this vehicle — documented repair instructions, service campaigns, or warranty extensions sent to dealers. A TSB isn't a recall (it's not a free safety remedy), but it's the manufacturer acknowledging the issue and how to fix it.
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
full bulletin at NHTSA ↗SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based
full bulletin at NHTSA ↗If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too mu
full bulletin at NHTSA ↗NISSAN: ALTIMA, MAXIMA, QUEST; POWER STEERING HOSE SERVICE PART CHANGE. THE HOSE NOW COMES WITHOUT THE PRESSURE SENSOR. DO NOT DAMAGE THE PRESSURE SENSOR UPON REMOVAL OR INSTALLATION. IF ONLY THE PRESSURE SENSOR NEEDS TO BE REPLACED, DO NOT REPLACE ANY HOSES.
full bulletin at NHTSA ↗Source: NHTSA manufacturer communications. Bring the bulletin number to your dealer or shop.
What owners are reporting 0 most recent
Common questions
How serious is the steering problem on the 2006 Nissan Quest?
It's a documented issue but not catastrophic. 4 complaints have been filed. Repairs average $700 and most owners catch it before it causes a breakdown.
At what mileage does the steering typically fail?
Based on the 4 complaints filed, steering issues most often appear around 52,952 miles. Some report problems earlier; some make it well past 150,000 with no symptoms. Maintenance habits matter — vehicles that received timely fluid services and were not regularly overworked tend to last longer.
What does it cost to fix?
Independent shops typically charge around $700 for steering repairs on this vehicle. Dealer pricing tends to run 20-40% higher. The exact figure depends on the specific failure mode, parts availability, and your local labor rates. If you're outside factory warranty, an extended service contract often covers this category.
Are there any recalls related to steering?
No active recalls currently cover steering issues on this vehicle. The complaints filed represent owner-reported failures that haven't risen to the level of a manufacturer-issued recall — but they're still worth knowing about before you buy or budget for repairs.