Plate - Planetary
full bulletin at NHTSA ↗2010 Jeep Commander powertrain problems
moderate Owners of the 2010 Jeep Commander have filed 4 NHTSA complaints about the powertrain at roughly $2,500 to repair (U.S. federal records, as of August 2026). Source: NHTSA Office of Defects Investigation. See powertrain across all vehicles →
Complaints
4
Recalls
0
Avg fix
$2,500
| Model year | powertrain complaints |
|---|---|
| 2006 Commander | 276 |
| 2007 Commander | 201 |
| 2008 Commander | 37 |
| 2009 Commander | 12 |
| 2010 Commander (this page) | 4 |
When does it fail?
Of the 4 powertrain complaints filed for the 2010 Jeep Commander, here's the actual mileage breakdown — failures cluster heaviest at 75,000-100,000 mi.
0-25k
25-50k
50-75k
75-100k
100-125k
125-150k
150k+
Each bar shows the share of total complaints filed at that mileage range. Peak failure window highlighted. Some owners report problems earlier; some make it well past 150,000 miles symptom-free. Maintenance habits and driving conditions shift the curve as much as mileage alone.
What stands out
Of the 5 model years of Jeep Commander we track for powertrain problems, this one has the fewest owner complaints on file (4).
No new NHTSA powertrain complaint has been filed on this vehicle in over 12 years — the issue may be aging out of the active population.
Is there a fix? Manufacturer service bulletins
The manufacturer has issued service bulletins covering powertrain on this vehicle — documented repair instructions, service campaigns, or warranty extensions sent to dealers. A TSB isn't a recall (it's not a free safety remedy), but it's the manufacturer acknowledging the issue and how to fix it.
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins
full bulletin at NHTSA ↗NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
full bulletin at NHTSA ↗NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
full bulletin at NHTSA ↗4WD Lamp Illuminated and Diagnostic Trouble Code C140F Active in Final Drive Control Modules (FDCM) Memory This bulletin involves verifying FDCM software level and then flash reprogramming of the FDCM with new software. Customers may indicate that the ?Service 4WD? indicator in the instrument cluster is illuminated. They may also indicate that the transfer case will not shift from 4WD High, 4WD Low, and/or Neutral once the lamp is illuminated. Further investigation identifies that a Diagnostic Trouble Code C140F is stored or active in the Final Drive Control Modules (FDCM) Memory
full bulletin at NHTSA ↗Source: NHTSA manufacturer communications. Bring the bulletin number to your dealer or shop.
What owners are reporting 1 most recent
Tl* the contact owns a 2010 Jeep commander. The contact stated that while driving approximately 35 MPH, the vehicle decelerated and proceeded to stall. The failure recurred various times at speeds below 40 MPH. The contact referenced NHTSA campaign number: 13v175000 (electrical system , power train) but was advised by the manufacturer that the VIN was not included in the recall. The vehicle was…
Had powertrain trouble with your 2010 Jeep Commander?
File a complaint with NHTSA → It's free, official, and how every report above got here — owner filings are the federal safety record this page is built on.
Common questions
How serious is the powertrain problem on the 2010 Jeep Commander?
It's a documented issue but not catastrophic. 4 complaints have been filed. Repairs average $2,500 and most owners catch it before it causes a breakdown.
At what mileage does the powertrain typically fail?
Based on the 4 complaints filed, powertrain issues most often appear around 69,275 miles. Some report problems earlier; some make it well past 150,000 with no symptoms. Maintenance habits matter — vehicles that received timely fluid services and were not regularly overworked tend to last longer.
What does it cost to fix?
Independent shops typically charge around $2,500 for powertrain repairs on this vehicle. Dealer pricing tends to run 20-40% higher. The exact figure depends on the specific failure mode, parts availability, and your local labor rates. If you're outside factory warranty, an extended service contract often covers this category.
Are there any recalls related to powertrain?
No active recalls currently cover powertrain issues on this vehicle. The complaints filed represent owner-reported failures that haven't risen to the level of a manufacturer-issued recall — but they're still worth knowing about before you buy or budget for repairs.
Related
Complaint and recall data sourced from the National Highway Traffic Safety Administration (NHTSA)
public records database. Verify the raw federal record at
nhtsa.gov/vehicle/2010/Jeep/Commander.
Severity ratings are derived from reported crashes, fires, injuries, and fatalities. Repair cost estimates are
independent-shop national averages and may differ in your area. Some links on this page are affiliate links.